Raymarine 465 Especificaciones Pagina 120
- Pagina / 132
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
110 RC435 and RC435i Chartplotters
interaction between different items of equipment, that is, to ensure
optimum Electromagnetic Compatibility (EMC).
Always report any EMC-related problem to your nearest Raymarine
dealer. We use such information to improve our quality standards.
In some installations, it may not be possible to prevent the equipment
from being affected by external influences. In general this will not
damage the equipment but it can lead to spurious resetting action, or
momentarily may result in faulty operation.
6.2 Resetting the System
Two types of reset are available for the Chartplotter:
• Power-On Reset: When you turn the display unit off, then on again,
the screen reverts to the chart display with all windows cleared.
• Factory Reset: This resets all values back to their original factory
settings. The factory default settings are listed in Chapter 4.
Note: Take care–factory reset clears all Waypoint and Route data-
bases.
To perform a factory reset:
1. Power off the unit.
2. Press and hold CLEAR while powering up until <Erase backup
procedure> is displayed.
3. Either press CLEAR to abort Factory Reset and resume normal
Power-Up or press ENTER to continue Factory Reset.
4. Press ENTER again; the unit restarts as for a first time Power Up
with all values reset to their original factory settings.
6.3 Problem Solving
Prior to packing and shipping, all Raymarine products are subjected to
comprehensive test and quality assurance programmes. However, if this
unit should develop a fault, please refer to the following table to identify
the most likely cause and the corrective action required to restore normal
operation.
If you still have a problem after referring to the table, contact your local
dealer, national distributor or Raymarine Technical Services for further
advice.
Always quote the product serial number.
81236_1.book Page 110 Monday, January 5, 2004 3:41 PM
- RC435 & RC435i 1
- Chartplotters 1
- About this Handbook 3
- Important Information 4
- Safety Notices 5
- Contents 7
- .......................... 38 8
- Chapter 1: Overview 11
- Trackpad and Cursor 12
- Dedicated Keys 13
- Status Bar 13
- Function Bar 13
- Pop-Up Menus 14
- Database Lists 14
- How it Works 15
- Chapter 2: Installation 17
- Suppression Ferrites 18
- Items Missing? 19
- Optional Items 19
- Registering this Product 19
- Surface Mounting 20
- Bracket Mounting 25
- Panel Mounting 25
- Antenna Connector 27
- POWER/NMEA Connector 28
- EMC Conformance 30
- System Check 30
- Initial Switch On 30
- SYSTEM SET UP 31
- Chapter 3: Getting Started 33
- 3.2 Switching On/Off 34
- 3.3 Simulator Mode 35
- 3.4 Controlling the Display 36
- Chapter 3: Getting Started 27 37
- Figure 3-1: Display Modes 37
- Moving Around the Chart 38
- Using FIND SHIP 38
- Changing the Chart Scale 39
- CSR 48°30.367'N 40
- POS 1°35.636'W 40
- BRG 231°T 40
- RNG 40.91nm 40
- Inserting a Gold Chart Card 42
- Removing a Gold Chart card 42
- Loading the Chart Data 43
- Displaying the Chart Data 44
- Chapter 4: Setting Up 45
- Bearing Mode 47
- Key Beep 47
- Simulator 49
- Simulated SOG 49
- Simulated COG 49
- 4.3 Chart Set Up Parameters 50
- Orientation 52
- Plotter Mode 52
- Anchor Alarm 54
- XTE Alarm 54
- Select Chart 54
- Chart Text 54
- 4.4 GPS Setup 56
- SD-FIX1.0 57
- ➤ To reset SD-GPS 58
- Chapter 5: Operation 59
- 5.2 Working with Waypoints 60
- Placing a Waypoint 61
- SIM NU 62
- Selecting a Waypoint 63
- Waypoint Data Display 64
- Editing Waypoint Details 65
- Erasing Waypoints 67
- Moving Waypoints 67
- 5.3 Working with Routes 68
- Creating a New Route 69
- Saving the Current Route 71
- Erasing or (re)Naming a Route 74
- Route Info 74
- Editing a Route 76
- Reverse a Route 79
- Follow a Route 79
- Join a Route 80
- Advance to a Waypoint 81
- Going to an Individual Target 82
- Go to a Waypoint 82
- Go to Cursor 83
- Go to a Port 84
- 5.5 Changing the Display Mode 85
- CDI Display 86
- BDI Display 87
- Waypoint Data 88
- Navigation Data 90
- Time/Date Data 91
- Managing Database Lists 93
- 5.7 Using Tracks 95
- Clearing the Current Track 97
- SmartRoute 97
- 5.8 Object Information 98
- 5.9 Using Archives 99
- 100
- 101
- Archiving a Track 102
- 103
- Archiving a Waypoint Set 105
- Port Services 109
- Tidal Height 111
- NANTUCKET 112
- Tidal Current 114
- ➤ To display Sun/Moon data: 115
- NANTUCKET HARBOR 116
- 5.11 Man Overboard (MOB) 117
- 5.12 Alarms 118
- 6.1 Maintenance 119
- 6.2 Resetting the System 120
- 6.3 Problem Solving 120
- Troubleshooting 121
- Accessories and Parts 122
- Technical Support 123
- Product Repair and Service 123
- Appendix A: Specifications 125
- NMEA Data 126
© 2020, manymanuals.es. Todos los derechos reservados | 0.129 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales