Raymarine V300 Información técnica descargar pdf (Pagina 21)

173

Maretron

Maretron Adapter Cords

MARE-005 The Raymarine E-Series product

to NMEA 2000 network adapter cable is used

to connect a Raymarine E-series product, such

as an E80 or E120 display, to an NMEA 2000

network. The cable is 1 meter in

length and has a female Raymarine

E-series connector on one end

and a standard male NMEA 2000

Micro series connector on the other end. Simrad SimNet product

to NMEA 2000 network adapter cable, manufactured by Simrad,

is used to connect a Simrad SimNet product like the NMEA 2000/

NMEA 0183 Adapter (AT10) or CX NavStation series products to

an NMEA 2000 network. The cable is 0.5 meters in length and has

a female SimNet connector on one end and a standard male NMEA

2000 Micro Series connector on the other end.

MRE MARE-002 NMEA2000 to Yamaha CMD

MRE MARE-005 Raymarine E-Series to NMEA2000

Maretron Tank Level Adapter

The TLA100 is used to adapt commercially

available resistive tank senders to the NMEA

2000 network. This allows you to observe tank

levels anywhere on the vessel where there are

NMEA 2000 compatible displays such as the

Maretron DSM250 or DSM200. The TLA100

is compatible with both the American standard

(240-30 ohm) and the European standard (10-

180 ohm) resistive senders. In fact, the TLA100

can be calibrated for any resistance between 0 and 300 ohms.

Unlike most tank senders that only work with rectangular tanks,

the TLA100 can be calibrated for irregular tank shapes so you

know the true level of the tanks. You can also use the TLA100

with analog gauges at the same time as NMEA 2000 so you don’t

he to e  estn nlo es to enoy the ntes of

digitally networked information.

NMEA 2000 Interface



Adapts American standard (240-30 ohm) resistive senders to 

NMEA 2000 Network

Adapts European standard (10-180 ohm) resistive senders to



NMEA 2000 Network

Calibrated for any resistance range from 0 to 300 ohms or 300 

to 0 ohms

Accommodates irregularly shaped tanks with 16 point 

calibration

16 Programmable tank types including fuel, fresh water, waste 

water, live well

Programmable tank number (s) up to 16 per tank type

Programmable tank capacity



Works alongside of analog gauges



Can be used standalone without analog gauges



MRE TLA100-01

Maretron

Alternating Current (AC) Monitor

Monitors AC power sources and outputs

information about these sources onto the industry

standard NMEA 2000 marine data network. The

ACM100 can monitor power busses, generators,

or utility power. ACM100 output information is then displayed with

networe N  eent sh s the retron 

dedicated display or with NMEA 2000 compatible software such

as Maretron N2KView. Best of all, the ACM100 is NMEA 2000

erte so yo n ew ny n ll  nforton nywhere on

the vessel using a compatible NMEA 2000 display. The ACM100

is a key component of Maretron’s N2KView vessel monitoring and

control system.

    

MRE ACM100-01

Maretron Direct Current (DC) Monitor

Maretron's DCM100 DC Monitor is an

advanced electronic monitoring device used

to measure the voltage and current of any

direct current (DC) power source or load.

les of  ower sores tht n e

monitored with the DCM100 include batteries,

alternators, solar panels, and wind generators.

The DCM100 can also be used to monitor DC loads like inverters,

windlasses, DC refrigerators, or any DC branch circuit. When the

DCM100 is used to monitor batteries, sophisticated circuitry and

software algorithms monitor battery temperature, load current,

charging current and terminal voltage to precisely compute battery

state of charge, state of health, and time remaining. To measure

current, the DCM100 uses an effect current sensor which simply

slips over the wire - you don't have to break connections or install

connectors as you do with inline shunts used by other solutions.

he 1 s N  erte so yo n ew ny n ll

DC information anywhere on the vessel using a compatible NMEA

2000 display. The DCM100 is a key component of Maretron's

N2KView vessel monitoring and control system.

    

MRE DCM100-01

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 79 80

Comentarios a estos manuales

Sin comentarios

Raymarine V300 Información técnica Pagina 21

Comentarios a estos manuales