Raymarine SmartPilot SPX-SAL Guia de preparacion descargar pdf (Pagina 35)

Chapter 2: Installing the system 27

SeaTalk

Connections

To connect your autopilot to a SeaTalk

backbone, use a dedicated spur cable. Spur

cables are available from your Raymarine dealer, as follows:

SeaTalk

power

The Course Computer does NOT supply power for SeaTalk

. A SeaTalk

system

must be powered from its own separate power supply.

See also

For more information on SeaTalk

systems refer to the separate reference guide

available from the Raymarine web site. www.raymarine.com/handbooks.

SeaTalk

spur cable length

Part number

1 ft 3 in (400 mm) A06038,

3 ft 3 in (1 m) A06039

9 ft 10 in (3 m) A06040

16 ft 4 in (5 m) A06041

A B

D10394-1

Cut back

Screen

Red

Cut back

& insulate

Yellow

Black

White

Blue

SeaTalk

spur cable

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 75 76

SmartPilot X-5R 1
Contents 3
Safety notices 7
EMC Conformance 7
Pressure washing 7
Warranty 8
Product disposal 8
1.1 Installation overview 9
Product documents 10
Example SeaTalk system 11
1.3 Equipment & Tools 12
2.1 Installation requirements 15
Power cable requirement 16
Mounting 17
D10375-1 18
2.4 Mounting the Drive 19
/4 inch diameter. If the 20
3/4 inch Steering Shaft 21
1 inch Steering Shaft 21
D10378-2 22
D10379-2 23
D10380-1 23
Step 5- Fit Drive unit 24
3/4 inch shaft fitting 25
1 inch shaft fitting 26
Watertight 27
Computer 28
2.6 Fluxgate Compass 29
Mounting procedure 30
Compass connection 30
Pilot Controller 31
D10644-1 32
D10645-1 32
2.8 Connect to ground 33
Rudder transducer 34
Connections 35
NMEA 0183 equipment 36
2.10Final checks 37
Requirement 39
Power assisted steering 39
Rudder reference information 39
3.1 Commissioning 40
D10646-1 42
Setup map 43
Align the rudder indicator 44
Set the rudder limits 44
Seatrial calibration 45
(see below) 46
Aligning the compass heading 47
AutoLearn 48
AutoLearn procedure 49
Before proceeding, ensure 50
Boat completes AutoLearn 51
Save new settings 51
3.2 Manual setup 52
Rudder gain 53
Counter rudder 54
AutoTrim 54
Rudder damping 55
4.1 Introduction 57
Adjusting calibration values 58
Accessing Display 59
Calibration 59
The RUDD BAR parameters are 59
Setting up data pages 60
Accessing User 61
4.4 Dealer calibration 62
Vessel type 63
Drive type 64
Align rudder 64
Rudder limit 64
Response level 65
Turn rate limit 66
Off course angle 66
PowerSteer 66
Cruise speed 67
Latitude 67
System reset 67
4.5 System defaults 68
NMEA0183 to Course Computer 69
Course Computer 71
Pilot Controller (ST6002) 73

Comentarios a estos manuales

Sin comentarios

Raymarine SmartPilot SPX-SAL Guia de preparacion Pagina 35

Comentarios a estos manuales

Relacionado con productos y manuales para Navegadores Raymarine SmartPilot SPX-SAL