Raymarine SeaTalk2 Guia de preparacion

SmartPilot X-5Sport Installation & Setup GuideDocument reference: 87076-1Date: March 200887076_1.book Page 1 Monday, March 10, 2008 2:57 PM

2 SmartPilot X-5 Sport Installation & Setup GuideProduct documentsThe SPX-5 Sport system consists of a number of components connected together usi

Chapter 1: Installation and system overviews 3Example SeaTalk systemSeaTalk allows connection of compatible products though a dedicated data bus, to a

4 SmartPilot X-5 Sport Installation & Setup Guide1.3 Equipment & ToolsBefore you begin ensure you have all the necessary components and tools

Chapter 1: Installation and system overviews 5Tools and equipment NOT suppliedYou will need to supply the following equipment and tools:Tools:• Flat b

6 SmartPilot X-5 Sport Installation & Setup Guide87076_1.book Page 6 Monday, March 10, 2008 2:57 PM

7Chapter 2: Installing the systemBefore proceeding with the installation, ensure you have the following to hand:• All necessary equipment and tools to

8 SmartPilot X-5 Sport installation & Setup GuideConnections to other equipmentIf Raymarine equipment is to be connected to other equipment using

Chapter 2: Installing the system 9The correct cable dimensions for various cable lengths are given in the following table. 2.3 SPX-5 Sport

10 SmartPilot X-5 Sport installation & Setup Guide D10375-1MOUNTVERTICALLY170 mm (6.7 in) 237 mm (9.33 in)56 mm(2.2 in)87076_1.book P

Chapter 2: Installing the system 11Connection overviewThe Course Computer provides the following system connections 2.4 Mounting the Sport

SeaTalk is a registered trademark of Raymarine Ltd. Raymarine, SeaTalk2, SeaTalkng, SmartPilot, AutoLearn, AutoTack, AutoTrim, GyroPlus and WindTrim

12 SmartPilot X-5 Sport installation & Setup Guide . Step 2 - Check wheel shaft sizeAs the way in which components are fitted depends

Chapter 2: Installing the system 13 Step 3– Prepare to fit torque restraint1. If the steering wheel shaft is 1 inch diameter, proceed from

14 SmartPilot X-5 Sport installation & Setup Guide3. Referring to the following illustration, identify a convenient surface that will pro-vide a s

Chapter 2: Installing the system 154. Offer up the torque restraint bracket to the mounting surface and mark the posi-tions for the securing screws.

16 SmartPilot X-5 Sport installation & Setup GuideStep 3 - Fit Sport Pilot driveIntroduction1. Secure the torque restraint to the mounting surface

Chapter 2: Installing the system 17Fitting to 3/4 inch steering shaft To fit the Sport Pilot drive to a 3/4inch steering shaft, refer to t

18 SmartPilot X-5 Sport installation & Setup Guide9. Slide the steering wheel onto the stub shaft, so that the woodruff key inserted at step 8 eng

Chapter 2: Installing the system 196. Offer up the stub shaft to the drive unit, ensuring the alignment marks on the stub shaft and drive unit are ali

20 SmartPilot X-5 Sport installation & Setup Guide2.5 Connecting power & drive cables to the Course ComputerPowerThe SPX-5 Sport system needs

Chapter 2: Installing the system 21At the Course Computer, locate the free ends of the cables from the distribution panel and SportDrive. Ensuring all

iContentsPreface ...vSafety n

22 SmartPilot X-5 Sport installation & Setup GuideMounting procedure1. Mount the Fluxgate Compass on a vertical bulkhead, with the cable leaving a

Chapter 2: Installing the system 232.7 Pilot ControllerFittingThe ST6002 Pilot Controller is supplied with an 4 m cable for connection to the SeaTalk

24 SmartPilot X-5 Sport installation & Setup Guide D10644-1SeaTalk power supplied by Course ComputerScreen PilotControlle

Chapter 2: Installing the system 252.8 Connect to groundCAUTION: GroundingThe SPX-5 Sport system ground MUST be connected to ship’s ground. Failure t

26 SmartPilot X-5 Sport installation & Setup Guide2.9 Optional connectionsRudder referenceFor suitable vessels, an optional rudder reference trans

Chapter 2: Installing the system 27SeaTalkng ConnectionsTo connect your autopilot to a SeaTalkng backbone, use a dedicated spur cable. Spur cables are

28 SmartPilot X-5 Sport installation & Setup GuideNMEA 0183 equipmentThe SPX-5 Sport system can connect via an NMEA port to NMEA devices such as a

Chapter 2: Installing the system 292.10Final checksWhen you have completed all necessary installation procedures, but before you apply power to the sy

30 SmartPilot X-5 Sport installation & Setup Guide87076_1.book Page 30 Monday, March 10, 2008 2:57 PM

31Chapter 3: Commissioning & SetupThis chapter describes the commissioning and setup procedures for your Raymarine SPX-5 Sport system.RequirementT

ii SmartPilot X-5 Sport Installation & Setup Guide2.7 Pilot Controller ...

32 SmartPilot X-5 Sport installation & Setup GuideDockside checks & setupThe dockside checks comprise:1. Switching on.2. Checking SeaTalk and

Chapter 3: Commissioning & Setup 33Step 2 - Check data connectionsPilot controllerCheck the SmartPilot controller links as follows:• With on the P

34 SmartPilot X-5 Sport installation & Setup Guide 4. Check that the rudder moves to starboard a few degrees and then stops.if the rud

Chapter 3: Commissioning & Setup 35 Entering Dealer calibrationEnter Dealer calibration as follows:1. Ensure the SPX-5 Sport system is

36 SmartPilot X-5 Sport installation & Setup GuideSet the vessel type as follows:1. Use -1 or +1 to select the appropriate type of boat:

Chapter 3: Commissioning & Setup 37Save the new settingsWhen you have adjusted the above settings, hold down standby for two seconds, to save your

38 SmartPilot X-5 Sport installation & Setup Guidedetermine the deviation and apply any correction required. The correction procedure reduces devi

Chapter 3: Commissioning & Setup 39Note: If necessary, you can quit the correction process by pressing standby or disp. If you then want to repea

40 SmartPilot X-5 Sport installation & Setup GuideAlthough the compass calibration removes most of the alignment error, small errors (a few degree

Chapter 3: Commissioning & Setup 41 Ensure you have sufficient sea room to complete the AutoLearn, then carry out the AutoLearn as fol

iiiChapter 4:SmartPilot X-5 Sport Settings ... 474.1 Introduction ...

42 SmartPilot X-5 Sport installation & Setup Guide3. With the AUTOLEARN screen displayed, prepare to start the AutoLearn: • power boats: steer str

Chapter 3: Commissioning & Setup 439. If the AutoLearn was successful, hold down standby for 2 seconds to store the new settings.Commissioning com

44 SmartPilot X-5 Sport installation & Setup GuideRudder gainBoats can vary widely in their response to helm, and by adjusting the rudder gain you

Chapter 3: Commissioning & Setup 45Counter rudder Counter rudder is the amount of rudder the SPX-5 Sport system applies to try to prevent the boat

46 SmartPilot X-5 Sport installation & Setup GuideTo adjust the AutoTrim1. Enter Dealer calibration as described on page 35.1. Use disp as necessa

47Chapter 4: SmartPilot X-5 Sport Settings4.1 IntroductionThis chapter describes the SPX-5 Sport system calibration settings and the factory default s

48 SmartPilot X-5 Sport installation & Setup GuideAccessing the Calibration modes Adjusting calibration valuesTo adjust calibration va

Chapter 4: SmartPilot X-5 Sport Settings 494.2 Display calibrationDisplay calibration provides settings to adjust the information displayed on the Pil

50 SmartPilot X-5 Sport installation & Setup GuideThe default page settings are:Setting up data pagesWhen setting up your data pages, we recommend

Chapter 4: SmartPilot X-5 Sport Settings 51Note: There are 3 depth pages (meters, feet and fathoms) and 2 water temperature pages (°C and °F). The SP

iv SmartPilot X-5 Sport Installation & Setup Guide87076_1.book Page iv Monday, March 10, 2008 2:57 PM

52 SmartPilot X-5 Sport installation & Setup Guide 4.4 Dealer calibrationFor information on how to access Dealer calibration, refer to

Chapter 4: SmartPilot X-5 Sport Settings 53 .Vessel type Selecting the correct vessel type, enables the SPX-5 Sport system to set appropri

54 SmartPilot X-5 Sport installation & Setup GuideDrive type The drive type setting controls how the SPX-5 Sport system drives the steering system

Chapter 4: SmartPilot X-5 Sport Settings 55Counter rudderCounter rudder is the amount of rudder the SPX-5 Sport system applies to try to prevent the b

56 SmartPilot X-5 Sport installation & Setup Guide Turn rate limitThis limits your boat’s rate of turn under SPX-5 Sport system contro

Chapter 4: SmartPilot X-5 Sport Settings 57 Cruise speedSets the cruise speed value to the boat’s typical cruising speed. If neither the s

58 SmartPilot X-5 Sport installation & Setup Guide3. The screen will then show an ARE YOU SURE message. Either:•Press auto to cancel the resetor•P

59 Appendix 1: NMEA 0183 sentencesThe SPX-5 Sport Course Computer computer supports the following NMEA0183 sentences.NMEA0183 to Course Computer

60 SmartPilot X-5 Sport installation & Setup Guide87076_1.book Page 60 Monday, March 10, 2008 2:57 PM

61 Appendix 2: SPX-5 Sport system specificationsCourse Computer Nominal supply voltage 12 V dc (20 A fuse protection at distribution panel

Preface vContentsPrefaceSafety notices EMC ConformanceAll Raymarine equipment and accessories are designed to t

62 SmartPilot X-5 Sport installation & Setup GuideSportDrive Nominal supply voltage 12 V dc Operating voltage range 10 V to 16 V dcEnv

63Pilot Controller (ST6002)Nominal supply voltage: 12 V dc via SeaTalkOperating voltage range: 10 V to 16 V dcCurrent consumption (Standby mode) 60

64 SmartPilot X-5 Sport installation & Setup Guide87076_1.book Page 64 Monday, March 10, 2008 2:57 PM

65IndexAAccessing calibration modes, 48AutoLearn, 40AutoTrim, 45, 55CCalibration modes, 47Certified installation, 1Checking system operation, 43Commis

66 SmartPilot X-5 Sport installation & Setup GuideOOff course warning angle, 56PParts supplied, 4Pilot Controllerconnecting, 23SeaTalk power NOT s

vi SmartPilot X-5 Sport Installation & Setup GuideTo the best of our knowledge, the information in the product documents was correct when they wen

Chapter 1: Installation and system overviews 1Chapter 1: Installation and system overviewsThis chapter gives an overview of installation procedures an